The dreaded 3M tape. It sticks to surfaces with the tenacity of an overly affectionate relative at a family reunion. Once it secures itself to a surface, good luck prying it off without taking some paint along as a souvenir. How to Remove 3M Tape Without Damaging Paint?!🤬
Heck, I successfully used Rapid Remover and Goo Gone to remove the (Nasty Diamond Shield) from the front of my 2009 class A RV. It worked wonders. I peeled off the clear 3M tape, sprayed the product on the remaining adhesive, waited for 60 minutes, and then used a “Plastic” (painter-style) scraper to remove it. It can get messy, but if you follow the instructions, it will get the job done!
Let us learn how to remove 3m tape without damaging paint.
Option 1: Use Googone to Remove 3M Tape Without Giving Your Paint Job a Panic Attack!
This guide will be your trusty weapon as we embark on an epic quest to vanquish the villainous vices of vexing vinyl tape.
Total Time: 30 minutes
Tape removal requires the surface to be properly prepared before you begin. Maintain a clean, dust-free environment around the tape.
Apply Goo Gone to the 3M tape
Apply a small amount of Goo Gone directly onto the tape, making sure to cover the entire area. Be careful not to apply too much, as this can damage the surface underneath the tape.
Let the Goo Gone sit for a few minutes
Allow the Goo Gone to penetrate the tape and soften the adhesive. This should take between 1-3 minutes, depending on the strength of the adhesive.
Use HTVRONT Vinyl Scraper to gently lift the edge of the tape
Slowly and carefully pull the tape away from the surface, using theHTVRONT Vinyl Scraper to help loosen the adhesive. Be patient and try not to rush the process, as this can cause the tape to tear or leave behind residue.
If there is any remaining adhesive left on the surface after removing the tape, use the Goo Gone and a clean microfiber cloth to dissolve it. Dab a small amount of Goo Gone onto the cloth and gently rub the adhesive until it dissolves. Be sure to test the Goo Gone on an inconspicuous area first, as it can damage some types of paint.
Estimated Cost: 9.9 USD
- Hair Dryer or Heat Gun
- Goo Gone Original Liquid
Materials: HTVRONT Vinyl Scraper
My Latest Updates
👋 Hi! This is Ronald. I just published 2 new articles you may enjoy reading. Feel free to keep reading this one or 👇 check out the new articles anytime.
I gave a detailed introduction of the theHTVRONT Vinyl Scraper in my article: How To Remove 3M Adhesive From Walls?
And Goo Gone in my article Goof Off Vs. Goo Gone | In-Depth Comparison
Option 2. Remove 3M Tape with Car Decal Adhesive Removal Tool Kit
Despite that, the wheel worked well, and I used it for hours. I had a Punisher skull decal on my car hood that was around 30 by 20 inches, and I used a Milwaukee m18 drill with about three batteries’ worth of charge. I followed up with a cutting compound and wax, and the decal was on the hood for over 3 years, but you can’t even tell I had one on in the first place.
The eraser works great, but it wears out fast. I used it to remove pinstripes from my older truck that were fading and wearing off. Some areas were stubborn, and the rubber on the tool wore down. Nevertheless, I still think it’s a good price since I can get the entire truck done, and the pads for polishing are a bonus. Overall, it’s a good deal that solved my issue!
I recommend you use this adhesive remover with a little water and soap, and it will work flawlessly. My vehicle’s paint was not damaged in any way, shape, or form. While some items in the set worked okay, the eraser fell apart after just five minutes of use. Buy an extra one if your 3M residue is large.