How to Fix Shot Glass With Glue?
You’ll need a clear epoxy adhesive or a specialized glass glue that dries transparent. Regular superglue may not be the best option as it can cause clouding or discoloration on the glass.
How to Fix Cracked Glass With Glue
Shot glasses are small and delicate, so take extra precautions when handling them, especially during the repair process. With patience and precision, you can successfully fix a broken shot glass and enjoy it for many more rounds of drinks with friends or as a decorative piece.
Total Time: 24 hours
Clean the Shot Glass
Use a small brush or a cotton swab to gently remove any glass shards or debris from the broken area. Be very careful while handling the broken pieces to avoid cuts. Rinse the shot glass with warm water and mild soap to ensure the surfaces are clean and free from residue.
Prepare the Surfaces
Lightly sand the broken edges of the shot glass with fine-grit sandpaper. This will help the glue adhere better to the glass surfaces. Wipe away any dust with a clean cloth.
Apply the Glue
Using a toothpick or a small wooden stick, apply a thin layer of epoxy or glass glue to one of the broken edges. Be very precise and avoid using too much glue, as it can create an unsightly appearance or even run down the sides of the shot glass.
Join the Pieces
Carefully align the broken edges and press them together firmly. Use a clamp or rubber bands to hold the pieces in place while the glue dries. This will ensure a tight, even bond.
Clean Up Excess Glue
If any glue squeezes out from the seam, gently wipe it away with a cotton swab dampened with a small amount of rubbing alcohol or acetone. Be careful not to let the solvent come into contact with the glued area, as it may weaken the bond.
Let It Cure
Follow the manufacturer’s instructions for the recommended curing time. Most epoxy or glass glues require at least 24 hours to fully cure and achieve maximum strength.
Inspect and Enjoy
Once the curing time has elapsed, carefully remove any clamps or rubber bands. Inspect the repaired shot glass for any imperfections or gaps. If the repair is successful, your shot glass is ready to be used again! Handle it with care, as the glued area may be slightly weaker than the original glass.
Supply:
- Elmer’s E1012 China and Glass Cement
Tools:
- You’ll also need a toothpick or a small wooden stick for applying the glue.
Materials: A clamp or rubber bands to hold the pieces together while drying
Why Are Shot Glasses Called Shot Glasses?
Shot glasses were first popular in the American Old West. Cowboys who wanted a drink but didn’t have the money for a whole glass would give the bartender one of their bullets in exchange for whiskey. The resulting beverage was called a shot, or “shot glass” of whiskey because of this practice.
Easier Way: DIY A New Shot Glass
Don’t Have to Fix Shot Glass
So if you are tired of repairing a shot glass, why not make one on your own?
Here is how to make it with decoration:
Step 1: Prepare the molds
Begin by selecting your favorite dried flowers and leaves. Carefully place them inside the shot glass silicone molds, arranging them in a visually appealing manner. Make sure the flowers and leaves are pressed against the sides and bottom of the molds.
Step 2: Mix the resin
In a mixing cup, pour equal parts of resin A and B. It’s crucial to maintain the correct ratio for the resin to cure properly. Stir the mixture for 5 minutes until it becomes clear, ensuring that both parts are thoroughly combined. Once the resin is clear, add a small amount of gold flakes to the mixture and stir gently to distribute them evenly.
Step 3: Pour the resin
To minimize the formation of bubbles, tilt the silicone molds at a slight angle. Slowly pour the resin mixture into the molds, filling them to the desired level. Be careful not to overfill the molds, as the resin will expand slightly during the curing process.
Step 4: Remove bubbles
After pouring the resin, you may notice some bubbles forming on the surface. To remove these bubbles, gently “burp” the molds by tapping them on a flat surface. This will help the bubbles rise to the surface and pop. Additionally, use a toothpick to carefully release any flowers or leaves that may have floated to the surface, ensuring they remain embedded in the resin.
Step 5: Eliminate remaining bubbles
To eliminate any remaining bubbles, spray a light mist of isopropyl alcohol over the surface of the resin. The alcohol will help break the surface tension, causing the bubbles to pop and disappear. Be careful not to spray too much alcohol, as it may affect the curing process.
Step 6: Let the resin cure
Allow the resin to cure according to the manufacturer’s instructions. This usually takes 24-48 hours, depending on the type of resin used and the ambient temperature. Place the molds in a dust-free area and avoid touching or moving them during the curing process.
Step 7: Demold and enjoy
Once the resin has fully cured, carefully demold your flower shot glasses. Gently bend the silicone molds to release the shot glasses. If needed, use a sharp knife to trim any excess resin along the edges for a clean and polished look.
Your DIY flower shot glasses are now ready to be admired and used. These unique and beautiful shot glasses will impress your guests and add a touch of elegance to your gatherings.
I’m Ronald Stevens, a Mechanical Engineer obsessed with adhesives, glue, and all things sticky! My passion began in childhood when I’d always be the one playing with glue during arts and crafts. And I’d spend hours researching and experimenting. Happy reading, and remember: stick with the best, and you’ll never be stuck in a mess!