JB Weld Vs Gorilla Glue: what’s the difference?
J-B Weld Original is steel reinforced, has a tensile strength of 5020 PSI and can withstand temperatures up to 550 degrees Fahrenheit (287 degrees Celsius); gorilla glue is nice for repositionable, gap filling, paintable, easy to dispense.
JB Weld Vs Gorilla Glue: Specs & Uses
⏰Cure Time
JB Weld: 16-24 hours
Gorilla Glue: 24 hours
🆚Working Time
JB Weld: 45 min max at 70°F
Gorilla Glue: 5-10 min (open assembly), 10-15 min (closed assembly) at 20°C, 50% RH
🛠️Common Uses
JB Weld is an ideal solution for repairing leaks in various tanks, such as oil lamps or fuel containers; UV-Resistant Bonding: bond outdoor fixtures or items exposed to sunlight; JB Weld’s “ExtremeHeat” variant is designed to withstand extreme temperatures up to 2400 degrees Fahrenheit.
Gorilla Glue can be used to repair shoes made from rubber, leather, canvas, or vinyl-plastic, waders or heels, fill small gaps or holes, or use a layer on the softer parts of the shoes to protect them from early damage.
Technical Info
I just did a test on JB Weld several days ago for an analysis of JB Kwik Vs. JB Weld and part of the data in the following test have some reference to that experiment.
My Hands-on Test of JB Weld
✅Pros: JB Weld
Even without any additional reinforcements, it’s still holding up strong.
Attach a PVC Right-Angle Elbow
I had been struggling to attach a PVC right-angle elbow 
to a Corian sink overflow hole, which is located on the upper part of the sink. Despite multiple attempts with other glues, the elbow would always slide and eventually disconnect. However, after realizing that the surfaces might be too smooth, I sanded both the PVC elbow and the sinkhole to create a rougher texture. This time, when I glued them together using J.B. Weld, it worked like a charm!
Fix My Kitchenaid Planetary Head
Another usage experience that impressed me was when I used JB Weld to fix my Kitchenaid planetary head. I had a model that didn’t have a pin to hold the head to the rotating shaft, rendering it unusable for about two years. But with JB Weld, I saw a solution. I cleaned the grease off both parts, mixed a small amount of the epoxy, and carefully applied it with a q-tip, ensuring it only went where needed. After allowing it to cure for two days, I tried it out, and the result was perfect. The planetary head was securely attached to the shaft, and I could finally use my Kitchenaid mixer again. I even tugged on the head to test its strength, and it didn’t budge.
Jb Weld Oil Pan Repair
When fully cured, J-B Weld Original is waterproof and resistant to petroleum, chemical and acid. So you can use JB weld for oil pan.
Does JB Weld work on stainless steel?
Yes, JB Weld bonds different materials together. It can be used to attach stainless steel towel bars to stainless steel wall fasteners, bond copper sheets to wood, and glue resin to cast metal.
Jb Weld Mower Deck Bracket
This repair was on a lawn mower deck, a really nice and clean job to do. I cleaned the parts of rust, grime and JB weld (it just wasn’t enough to hold), repositioned the bracket, welded solid both sides (with internal weld) and applied flat black paint to protect from rust.
In this day and age, save your hard earned money!
❌Cons: JB Weld
Cure time: J.B. Weld requires a significant amount of time to fully cure and reach its maximum strength. The recommended cure time is 24 hours, which means you need to wait patiently before subjecting the repaired item to stress or load. This can be inconvenient if you’re looking for a quick fix.
What Will Jb Weld Not Stick To?
Broadly speaking, most J-B Weld products will not adhere or bond well to: Any flexible rubber surface. Canvas. Polypropylene plastic.
💬 FAQ of JB Weld Original
Q: Does this adhesive have UV resistance?
A: Yes, this particular two-part epoxy is resistant to UV rays. Its high concentration of metallic powder enhances its resistance. Additionally, you can paint over it for added protection.
Q: Will JB Weld hold a small piece of metal fuel port from a carburetor in a horizontal position until it sets? Or will gravity cause it to detach? It has a 4-6 hour set time.
A: If there is weight pulling on it, it might slip. I recommend using painter’s tape to hold it in place until it hardens. Avoid starting or operating the vehicle until the adhesive has fully set. However, if the piece will come into contact with fuel, this adhesive may not be suitable.
Q: I have a tiny nick in an injector seat. Could I use JB Weld to fill it?
A: It could work if you shape and sand it smooth. Your injector O-ring should seal it off, though.
Q: How much surface area can one pack of JB Weld cover? I need to attach a 2ft x 1ft aluminum sheet to wood.
A: One package might be sufficient, depending on the thickness and application method.
Q: Can I use JB Weld on silver? I have a silver candlestick with a broken bottom. A jeweler said it’s too big for him to repair.
A: This adhesive functions like welding material, but it won’t match the color of silver. I would recommend using it only if the repair won’t be visible, and be careful to prevent any excess adhesive from squeezing out the sides.
Q: I want to bond a piece of stainless steel to an Alumawood ceiling and hang a 3.65-pound light with magnets. Will JB Weld adhesive work?
A: Based on my personal experience, I successfully hung a heavy triple shampoo/body wash/conditioner wall dispenser on a vikrell tub/shower surround wall using this adhesive. It held up solidly, even with the weight. It’s stronger than typical glues like Gorilla Glue
. So, based on that experience, I believe it can easily support 4 pounds. I’ve also used it to fix and reattach a broken wheel on a cart, and it worked amazingly well. I highly recommend this adhesive!
Q: I’m attempting to reattach a wooden handle to a cast iron enamel Descoware frying pan (made in Belgium). Will JB Weld product work?
A: JB Weld’s “ExtremeHeat” variant is specifically designed for exhaust manifolds and tailpipes, withstanding temperatures up to 2400 degrees Fahrenheit.
I just did a test on Gorilla Glue several days ago for an analysis of Krazy Glue Vs. Gorilla Glue and part of the data in the following test have some reference to that experiment.
7 reviews
📣🔥 Share it to easily keep track of the answers!
Leave a Reply
My Hands-on Test of Gorilla Glue
✅Pros
I applied a dime-sized dollop on each corner of the painted cinderblock, deviating slightly from the recommended squiggly line application. I wanted to ensure easy removal of the screen frame in the future, so I opted for a more conservative amount.
Fixed Suitcase’s Handle
One example of my use so far was when the decorative silver strip on my suitcase’s pull-out handle was popping out. Before it broke off and caused either an injury to the hand or weakened the handle, I decided to apply the Gorilla Glue to reattach it permanently.
And by permanently, I mean it! This glue should hold that silver strip in place long after the rest of the suitcase is destroyed!
It is 2X Stronger than Gorilla Heavy Duty Construction Adhesive Ultimate 
.
Convenience
What impressed me further was the convenience of this glue. It comes in the perfect amount for small jobs, and its hold is excellent with a quick setting time. I appreciate that the tube has a screw cap, allowing me to close it up and save any remaining glue for later use. This adds to the overall value and longevity of the product.
❌Cons
However, there are some precautions to keep in mind when using this glue. For instance, I had to be careful while cleaning the nozzle after each use since moistening the nozzle with a towel can solidify the fresh gel almost instantly onto the nozzle. It is easier to let the gel dry a bit and break off the dried gel.
💬 What U May Be Interested in Gorilla Glue
Q: Is it safe to use Gorilla Super Glue Gel on glass surfaces?
A: We don’t advise using Gorilla Super Glue Gel on the glass as the bond may weaken over time due to the alkalinity in the glass.
Q: Can I use this to bond stainless steel to stainless steel?
A: Yes, it should work.
Q: Is it possible to use this to bond steel to wood?
A: I wouldn’t recommend using this glue for that purpose. I suggest using an epoxy resin for a strong bond instead.
Q: Does Gorilla Super Glue Gel work well on nails?
A: Yes, it works but as is said in 
Nail Glue vs Super Glue: nails are porous and can absorb toxins and chemicals present in super glue, which then enter your bloodstream.
Q: Where can I find the Gorilla Glue?
A: I was searching for the Gorilla Glue I usually use and stumbled upon it.
Q: Can I use Gorilla Super Glue Gel to bond a silicone gasket to steel containers?
A: Hello, Gorilla Super Glue Gel works on steel surfaces, but gluing silicone is considered “trial and error.”
Q: Why do I need to mist water when using Gorilla Glue?
A: Gorilla Super Glue doesn’t require water. Only Original Gorilla Glue needs water since it is a moisture-curing polyurethane.
Q: Is it possible to use this to glue a ceramic tile to a wooden picture frame?
A: Yes, you can use it if the tile is already self-adhesive and you want to reinforce it. Once applied, make sure the glue is completely dried for a period of time.
Q: Is Gorilla Super Glue Gel safe for use on Styrofoam?
A: I have found it to adhere to everything, but I cannot advise on the fumes when working with Styrofoam.
Q: Can I use it to fix a handle on a microwave?
A: Yes, I used it to fix a plastic knob on my dryer, so it might work for your microwave handle.
Q: Will it hold decorative plates on the wall?
A: It is strong enough to hold decorative plates on the wall, but when you reposition or remove the plates, the glue may rip a big hole in the wall. Therefore, I wouldn’t recommend it for this application.
Q: Can Gorilla Super Glue Gel be used to bond aquarium ornaments?
A: Gorilla Super Glue Gel isn’t waterproof, and we cannot confirm it’s non-toxic once cured. We also don’t advise using Gorilla Glue products in applications that could lead to direct food contact or consumption or in situations where glue may be ingested.
Q: Can I use this glue to attach something to the wall?
A: Yes, Gorilla Super Glue Gel works on most surfaces and is thick enough to be used for vertical applications.
Q: What’s the difference between 102433xl & 7700104 or the best glue under constant twisting pressure?
A: Gorilla Super Glue products dry rigid and not flexible.
Q: Can I use Gorilla Super Glue Gel to bond vinyl to EPO foam?
A: We don’t recommend using Gorilla Super Glue Gel on foam materials it may dissolve or eat away at foam. For bonding vinyl to EPO foam, we recommend using a specialized adhesive designed for foam materials, please refer to this article: 6 Best Adhesive For Foam Board To Metal.
I’m Ronald Stevens, a Mechanical Engineer obsessed with adhesives, glue, and all things sticky! My passion began in childhood when I’d always be the one playing with glue during arts and crafts. And I’d spend hours researching and experimenting. Happy reading, and remember: stick with the best, and you’ll never be stuck in a mess!
Feel free to contact me and join our discussion:
I'm attempting to reattach a wooden handle to a cast iron enamel Descoware frying pan (made in Belgium). Will JB Weld product work?
Yes sure. JB Weld’s “ExtremeHeat” variant is specifically designed for exhaust manifolds and tailpipes, withstanding temperatures up to 2400 degrees Fahrenheit.
Can I use JB Weld to fix a leak in the tank of my vintage Dietz oil lamp?
It should work if the surface is clean without any oil film. Once it cures, it won't be affected by oil.
Ronald , I need to glue canvas to glass on a convertible top. What do you suggest?
Hi Don, try 3M Marine Adhesive 4200: https://www.stickyaides.com/a/lifecaulk-vs-4200/#my-handson-test-3m-marine-adhesive-4200. It's known for its high strength, flexibility, and ability to adhere to tough surfaces like canvas and glass. It’s designed to withstand harsh weather and movement, which is essential for a convertible top.Read More
Hi Don, try 3M Marine Adhesive 4200: https://www.stickyaides.com/a/lifecaulk-vs-4200/#my-handson-test-3m-marine-adhesive-4200. It’s known for its high strength, flexibility, and ability to adhere to tough surfaces like canvas and glass. It’s designed to withstand harsh weather and movement, which is essential for a convertible top.
Show Less
This glue is TERRIBLE! Do not buy it. I glued a handle to a ceramic mug last SATURDAY today is THURSDAY and I am still waiting for it to dry!! 😳 Keep advertising on Google and I will keep posting my comments of my experience! 😕 It said that it could be used on ceramic. Then I cleaned the handle…Read More
This glue is TERRIBLE! Do not buy it. I glued a handle to a ceramic mug last SATURDAY today is THURSDAY and I am still waiting for it to dry!! 😳 Keep advertising on Google and I will keep posting my comments of my experience! 😕 It said that it could be used on ceramic. Then I cleaned the handle with Mr Clean clean freak and everything fell apart. Very disappointed from your advertisement…..
Show Less